NEWS

Compact navigation light with 13mm diameter!The positional of the 13mm class has a light output of up to 150 lumens and can be easily mounted on any surface thanks to its flat design. The heat development is low and well suited for operation in the air. The diameter refers to the size of the cap.These new round lights come with a snap-on cylindrical and spherical cap made from highly transparent polycarbonate. The selection and gluing is done directly on the model, suitable glues are e.g. transparent epoxy or Uhu Por.Specifications:Electric: 2W reference power with x2 technology, 8V / 12V, 0.18ABeam angle: 360 °Light intensity: ~ 60 lumens REDLight intensity: ~90 lumens GREENLight intensity: ~ 150 lumens WHITEDimension: D13x13mm Zylinder, 13x11mm Roundcapgroundplate : 16x4mmWeight: 1g (without cable) RND13X-022x2-WE

LED light strip, can be shortened in 16 mm increments.Technical dataWidth = 4mmLength = 1 meter in one pieceWeight = only 3.5g per meterOperating voltage = 6 -8VBack = self-adhesive (protective film) 15317

LED light strip, can be shortened in 16 mm increments.Technical dataWidth = 4mmLength = 1 meter in one pieceWeight = only 3.5g per meterOperating voltage = 6 -8VBack = self-adhesive (protective film) 15318

LED light strip, can be shortened in 16 mm increments.Technical dataWidth = 4mmLength = 1 meter in one pieceWeight = only 3.5g per meterOperating voltage = 6 -8VBack = self-adhesive (protective film) 15319

LED light strip, can be shortened in 16 mm increments.Technical dataWidth = 4mmLength = 1 meter in one pieceWeight = only 3.5g per meterOperating voltage = 6 -8VBack = self-adhesive (protective film) 15320

LED light strip, can be shortened in 16 mm increments.Technical dataWidth = 4mmLength = 1 meter in one pieceWeight = only 3.5g per meterOperating voltage = 6 -8VBack = self-adhesive (protective film) 15321

LED light strips, can be shortened in 16mm steps. 15307

LED light strips, can be shortened in 16mm steps. 15308

LED light strips, can be shortened in 16mm steps. 15309

LED light strips, can be shortened in 16mm steps. 15311

LED light strips, can be shortened in 16mm steps. 15306

LED light strip, can be shortened in 5cm steps (household scissors). C4326

LED light strip, can be shortened in 5cm steps (household scissors). C4324

LED light strip, can be shortened in 5cm steps (household scissors). C4327

LED light strip, can be shortened in 5cm steps (household scissors). C4325

LED light strip, can be shortened in 5cm steps (household scissors). C4323

The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.Note: The LED lights are extremely bright! Never look directly into a LED!Technical DataElectricity: 8W reference power, 8(12)V, 0.35ABeam angle: >160°Light intensity: ~100 Lumen REDLight intensity: ~140 Lumen GREENLight intensity: ~190 Lumen WHITEDimension cooling tube: D10x45mm, flange D12mmDimension light cap: D10x12.5mm, flange for carrier D12mmTotal mass: D10/12mm, 57.5mm lengthWeight: 5g (without cable) PIN10F-040x2-RT

Short high-power light with 4W reference power for flash operation on small models. The pen light is delivered pre-assembled and ready for use on a CNC-manufactured aluminum heat sink, with 5 high-strength polycarbonate caps for free use:1x 10mm cylinder cap1x 10mm round cap1x 13mm cylinder claw1x 13mm round capand 1x profile extension 10mmThe reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.Note: The LED lights are extremely bright! Never look directly into a LED!TECHNICAL DATAElectricity: 4W reference power, 8(12)V, 0.35ABeam angle: >160°Light intensity: ~50 Lumen REDLight intensity: ~80 Lumen GREENLight intensity: ~120 Lumen WHITETotal Dimension: D10x37mm, flange D12mmDimension heatsink: D10x25mmWeight: 4g (without cable) PIN10X-040-GN

Short high-power light with 4W reference power for flash operation on small models. The pen light is delivered pre-assembled and ready for use on a CNC-manufactured aluminum heat sink, with 5 high-strength polycarbonate caps for free use:1x 10mm cylinder cap1x 10mm round cap1x 13mm cylinder claw1x 13mm round capand 1x profile extension 10mmTechnical Data:Electricity: 4W reference power, 8(12)V, 0.35ABeam angle: >160°Light intensity: ~50 Lumen REDLight intensity: ~80 Lumen GREENLight intensity: ~120 Lumen WHITETotal Dimension: D10x37mm, flange D12mmDimension heatsink: D10x25mmWeight: 4g (without cable) PIN10X-040-WE

73031

73032

With our new night flight blades a simple, indirect illumination of the tail of most models up to 2 meters wingspan is suitable. At a few grams they provide enormous light output without affecting the flight characteristics. uniLIGHT Night BladesCompact dimensions with maximum performance Minimal effect on flight behaviour Novel cable and plugless assembly Optimized, adjustable cooling reflector Reduced self-glare 5 sizes for all rods especially for wings and symmetrical for the tail unit Asymmetrical design for maximum robustness Safety holder with position light available large systems as cable and autonomous battery version Installation and operationFirst glue the enclosed small contact plate firmly into the wingtips, sides or also at the elevator, preferably with good epoxy and optional pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In top view, the right is always a plus. The connection cable is routed centrally to the fuselage within the surface. All Night-Blades can simply be operated in parallel on a 2S LiPo battery, or also on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off during deep discharge at night could be fatal! For commissioning, simply place the Night-Blade with the two screws on the mounting plate and tighten, the electrical contact is made automatically. Make sure that the labels are always legibly oriented. The reflector surfaces are bent once so that the largest possible part of the light emission is directed onto the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before you align the surfaces by hand or a small pair of pliers to prevent the glued area from breaking open. After the flight the Night-Blades can easily be unscrewed and transported. No trace of the night flight system remains. Technical SpecificationsStructure: 1.5mm GRP support, symmetricalElectric: 8V, 0.65ALuminous intensity: ~550 Lumen WHITETotal dimension: 150x36mmWeight: 12g (without cable)Delivery: with mounting plate for wireless connection, 1m connection cable, ready-made for direct operation with 2S LiPo and any uniLIGHT lighting controller NIGHT-M-TAIL

With our new night flight blades a simple, indirect illumination of almost all larger models up to 3m span is suitable. The delicate but very robust CFRP tube construction provides enormous light output at low weight without affecting the flight characteristics. When delivered, the tubes and plates are only pre-assembled and can still be shortened and aligned on the model. This ensures optimum illumination. Only then are the arms finally fixed with a few drops of epoxy. An asymmetrical mounting is also possible (short arm near the floor).uniLIGHT Night BladesCompact dimensions with maximum performance Minimal effect on flight behaviour Novel cable and plugless assembly Optimized, adjustable cooling reflector Reduced self-glare 5 sizes for all rods especially for wings and symmetrical for the tail unit Asymmetrical design for maximum robustness Safety holder with position light available large systems as cable and autonomous battery version Installation and operationFirst glue the enclosed small contact plate firmly into the wingtips, sides or also at the elevator, preferably with good epoxy and pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In top view, the right is always a plus. The connection cable is routed centrally to the fuselage within the surface. All Night-Blades can simply be operated in parallel on a 2S LiPo battery, or also on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off during deep discharge at night could be fatal! For commissioning, simply place the Night-Blade with the two screws on the mounting plate and tighten, the electrical contact is made automatically. Make sure that the labels are always legibly oriented. With the L and XL systems, the light panels must be aligned once on the model during initial assembly and fixed with a little epoxy. Then reflector surfaces are bent once so that the largest possible part of the light emission is directed onto the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before you align the surfaces by hand or a small pair of pliers to prevent the glued area from breaking open. After the flight the Night-Blades can easily be unscrewed and transported. No trace of the night flight system remains. Technical SpecificationsConstruction: GFK/Aluminium mixed construction, 6mm CFK tube, pre-assembledElectrical: 8V, 2.5ALuminous intensity: ~1500 Lumen WHITETotal dimensions: 295x57mmWeight: 51g (without cable)Delivery: with mounting plate for wireless connection, 1m connection cable, ready-made for direct operation with 2S LiPo and any uniLIGHT lighting controller NIGHT-XL-WING

Set for easy mounting and contacting of the LARGE and XLARGE DIY-Set. The set includes safety mounting plates that include a second circuit with a red and a green side light in addition to the mechanical fixtures. Thus, in the event of a defect, the fundamental position detection remains, a new safety feature for night flights! uniLIGHT Night BladesCompact dimensions with maximum performance Minimal effect on flight behaviour Novel cable and plugless assembly Optimized, adjustable cooling reflector Reduced self-glare 5 sizes for all rods especially for wings and symmetrical for the tail unit Asymmetrical design for maximum robustness Safety holder with position light available large systems as cable and autonomous battery version Installation and operationFirst glue the enclosed small contact plate firmly into the wingtips, sides or also at the elevator, preferably with good epoxy and optional pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In top view, the right is always a plus. The connection cable is routed centrally to the fuselage within the surface. All Night-Blades can simply be operated in parallel on a 2S LiPo battery, or also on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off during deep discharge at night could be fatal! For commissioning, simply place the Night-Blade with the two screws on the mounting plate and tighten, the electrical contact is made automatically. Make sure that the labels are always legibly oriented. The reflector surfaces are bent once so that the largest possible part of the light emission is directed onto the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before you align the surfaces by hand or a small pair of pliers to prevent the glued area from breaking open. After the flight the Night-Blades can easily be unscrewed and transported. No trace of the night flight system remains. Technical SpecificationsSuperstructure: 1.5mm GRP beamTotal dimension: 7.5x57/80mmDelivery: four mounting plates for wireless connection of two wing blades and two tail blades, 1m connection cable each, ready-made for direct operation with 2S LiPo and each uniLIGHT lighting controller NIGHT-LXL-CONRG

The ACCU based night flight blades are the simplest method to illuminate large models indirectly. Based on the normal LARGE and XLARGE systems, a central battery holder is provided on each Light-Blade to accommodate a small, weight-optimized LiPo battery. This is simply snapped in and held in place with mounting rings - the system is active. The LARGE system can only be used with a full battery for a flight of 8-10 minutes. The delicate but very robust CFRP tube construction provides enormous light output at low weight without strongly influencing the flight characteristics. Compared to the wired systems, the light output of the lightweight battery systems is slightly lower, but the system is immediately ready for operation and no cables or soldering work on the surface is required. When delivered, the tubes and plates are only pre-assembled and can still be shortened and aligned on the model. This ensures optimum illumination. Only then are the arms finally fixed with a few drops of epoxy. An asymmetrical mounting is also possible (short arm near the floor). uniLIGHT Night BladesCompact dimensions with maximum performance Minimal effect on flight behaviour Novel cable and plugless assembly Optimized, adjustable cooling reflector Reduced self-glare 5 sizes for all rods especially for wings and symmetrical for the tail unit Asymmetrical design for maximum robustness Safety holder with position light available large systems as cable and autonomous battery version Installation and operationFirst of all, the supplied mounting plate can be glued firmly into the wing tips, preferably with good epoxy and pins. Connection cables are not required. With the L and XL systems, the light panels must be aligned once on the model during initial assembly and fixed with a little epoxy. Then reflector surfaces are bent once so that the largest possible part of the light emission is directed onto the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before you align the surfaces by hand or a small pair of pliers to prevent the glued area from breaking open. After the flight the Night-Blades can easily be unscrewed and transported. No trace of the night flight system remains. Technical SpecificationsConstruction: GFK/Aluminium mixed construction, 5mm CFK tube, pre-assembledElectrical: 8V, 1.8AOperating time: 8-10 minutesSafety: integrated safety position light, can also be switched off by means of solder jumpers to extend running timeLuminous intensity: ~1000 Lumen WHITETotal dimension: 310x85mmWeight: 2x67gDelivery: 2x LARGE Wing-Blades, 2x LIPO-330 batteries, 2x mounting plate, 2x cap for safety light, 4x mounting ring NIGHT-L-ACCU

Small and light black anodized scale-searchlight CNC manufactured aluminium reflector with 24mm diameter and scale details with focusing 30° lens and x2 Chip for best light output. Including 2-arm mounting bracket.Direct operation with 2S LiPo (8V). With 3S (12V), the additional resistor has to be soldered in or use a 4W connection cable (accessories). Please ensure sufficient cooling air during operation. Without any further flow, do not operate the spotlights more than 5-10 minutes at a time.Technical Data:Performance: 4Wx2 reference powerVoltage: 8V, use enclosed resistor additionally for 12V!Electricity: 0.35ABeam angle: ~30°Light intensity: ~190 Lumen WHITELight intensity: ~170 Lumen WARMWHITEDimension: D24x26mmWeight: 16g (without cable) SRC24-040x2-WE

Position light optimized for functionality with enormous luminosity for all sports tasks. The lights are perfect for lighting all multicopters, sport jets, trainer helicopters, sailors,... These are three emitters on an aluminium carrier with a matching, extremely slim polycarbonate cover. The lamps are designed for direct operation with 2S/8V Lipo and can also be operated at 12V/3S with the supplied resistor.Please note that high-power LEDs can become very warm, up to 70°C is quite normal. These luminaires should be placed in the air stream. Lying heat sink for horizontal or vertical mounting. BAR5-030x2-WE

PUREX-040-WE

Flat Ultra-Power spotlight with up to 400 Lumen, CNC manufactured aluminium reflector with 26mm diameter. The spotlight must be glued directly on the gear leg with thermal conductive adhesive. Attention: This Ultra-Power luminaire has no temperature protection, a heat bridge connection to the carrier (undercarriage leg) is highly recommended.Direct operation with 2S LiPo (8V). With 3S (12V), the additional resistor has to be soldered in or use a 8W connection cable (accessories). Please ensure sufficient cooling air during operation.Technical Data:Performance: 8Wx2 reference powerVoltage: 8V, use enclosed resistor for 12V, 0.7ABeam angle: ~100°Electricity: 0.7ALight intensity: ~400 Lumen WHITELight intensity: ~350 Lumen WARMWHITEDimension: D26x11mmWeight: 10g (without cable) SPOT26X-080x2-WE

SPOT15F-080-3x-WE