NEWS

Universal lamp covers made of clear, deep-drawn acrylic. Ideally suited for model lighting, position lights etc..Round shape with diameters of 20, 15 and 10 mm, long shape with lengths of 50, 40 and 35 mm (each 15 mm wide). C8433

CABLE-CLIP-S

Set for easy mounting and contacting of the XSMALL DIY Set. The set includes safety mounting plates that include a second circuit with a red and a green side light in addition to the mechanical fixtures. Thus, in the event of a defect, the fundamental position detection remains, a new safety feature for night flights! uniLIGHT Night BladesCompact dimensions with maximum performance Minimal effect on flight behaviour Novel cable and plugless assembly Optimized, adjustable cooling reflector Reduced self-glare 5 sizes for all rods especially for wings and symmetrical for the tail unit Asymmetrical design for maximum robustness Safety holder with position light available large systems as cable and autonomous battery version Installation and operationFirst glue the enclosed small contact plate firmly into the wingtips, sides or also at the elevator, preferably with good epoxy and optional pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In top view, the right is always a plus. The connection cable is routed centrally to the fuselage within the surface. All Night-Blades can simply be operated in parallel on a 2S LiPo battery, or also on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off during deep discharge at night could be fatal! For commissioning, simply place the Night-Blade with the two screws on the mounting plate and tighten, the electrical contact is made automatically. Make sure that the labels are always legibly oriented. The reflector surfaces are bent once so that the largest possible part of the light emission is directed onto the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before you align the surfaces by hand or a small pair of pliers to prevent the glued area from breaking open. After the flight the Night-Blades can easily be unscrewed and transported. No trace of the night flight system remains. Technical SpecificationsSuperstructure: 1mm GRP beamTotal dimension: 5x28/38mmDelivery: three mounting plates for wireless connection of two wing blades and one tail blade, 0.5m connection cable, ready-made for direct operation with 2S LiPo and each uniLIGHT lighting controller NIGHT-XS-CONRG

Set for easy mounting and contacting of the SMALL DIY-Set. The set includes safety mounting plates that include a second circuit with a red and a green side light in addition to the mechanical fixtures. Thus, in the event of a defect, the fundamental position detection remains, a new safety feature for night flights!uniLIGHT Night BladesCompact dimensions with maximum performance Minimal effect on flight behaviour Novel cable and plugless assembly Optimized, adjustable cooling reflector Reduced self-glare 5 sizes for all rods especially for wings and symmetrical for the tail unit Asymmetrical design for maximum robustness Safety holder with position light available large systems as cable and autonomous battery version Installation and operationFirst glue the enclosed small contact plate firmly into the wingtips, sides or also at the elevator, preferably with good epoxy and optional pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In top view, the right is always a plus. The connection cable is routed centrally to the fuselage within the surface. All Night-Blades can simply be operated in parallel on a 2S LiPo battery, or also on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off during deep discharge at night could be fatal! For commissioning, simply place the Night-Blade with the two screws on the mounting plate and tighten, the electrical contact is made automatically. Make sure that the labels are always legibly oriented. The reflector surfaces are bent once so that the largest possible part of the light emission is directed onto the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before you align the surfaces by hand or a small pair of pliers to prevent the glued area from breaking open. After the flight the Night-Blades can easily be unscrewed and transported. No trace of the night flight system remains. Technical SpecificationsSuperstructure: 1.5/1mm GRP beamTotal dimension: 5x28/38mmDelivery: three mounting plates for wireless connection of two wing blades and one tail blade, 0.5/1m connection cable, ready-made for direct operation with 2S LiPo and each uniLIGHT lighting controller NIGHT-S-CONRG

Set for easy mounting and contacting of the MEDIUM DIY-Set. The set includes safety mounting plates that include a second circuit with a red and a green side light in addition to the mechanical fixtures. Thus, in the event of a defect, the fundamental position detection remains, a new safety feature for night flights! uniLIGHT Night BladesCompact dimensions with maximum performance Minimal effect on flight behaviour Novel cable and plugless assembly Optimized, adjustable cooling reflector Reduced self-glare 5 sizes for all rods especially for wings and symmetrical for the tail unit Asymmetrical design for maximum robustness Safety holder with position light available large systems as cable and autonomous battery version Installation and operationFirst glue the enclosed small contact plate firmly into the wingtips, sides or also at the elevator, preferably with good epoxy and optional pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In top view, the right is always a plus. The connection cable is routed centrally to the fuselage within the surface. All Night-Blades can simply be operated in parallel on a 2S LiPo battery, or also on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off during deep discharge at night could be fatal! For commissioning, simply place the Night-Blade with the two screws on the mounting plate and tighten, the electrical contact is made automatically. Make sure that the labels are always legibly oriented. The reflector surfaces are bent once so that the largest possible part of the light emission is directed onto the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before you align the surfaces by hand or a small pair of pliers to prevent the glued area from breaking open. After the flight the Night-Blades can easily be unscrewed and transported. No trace of the night flight system remains. Technical SpecificationsSuperstructure: 1.5mm GRP beamTotal dimension: 7.5x57/80mmDelivery: three mounting plates for wireless connection of two wing blades and one tail blade, 1m connection cable, ready-made for direct operation with 2S LiPo and each uniLIGHT lighting controller NIGHT-M-CONRG

Quadling strand for RGB LED-Stripes in the colours black-green-red-blue 4x0,25mm². 419-010

CAPS-MINI

Very high-quality, convex collecting lenses for mounting on 30mm headlights (9708936 ; 9708937 ), very high optical quality. CAPS-L30

Ready assembled extension cable with 1m length and integrated series resistor in order to operate 8W high-performance lights on 3S without soldering. Ready built up with double-sided plug connection. CABLE-8W-3S

Ready assembled adapter cable with 1m length to operate two lights directly at one output of the controller without soldering. CABLE-Y

Our recommended cabling. Optimated for medium sized uniLIGHT lightsystems. NEW ! cable with different profile causes the best performancce on minimal weight.The set containsTwo cables for wings made from 4-pole Teflon for combilights and spotlights, all with a length of 2m and connector, coding: orange, black, gray, whiteThree single cable with flexible siliconcable for installation on the fuselage, all with a length of 2m and connector CABLE-UNI

Round assembly housing for high-performance LED modules. The housings consist of transparent polycarbonate caps and associated aluminium base plates, which work as heatsinks. A small (preferable for 4W LEDs) and a big (for 8W LEDs) base plate is included. With these cooling plates, the LEDs are suitable for continuous operation with air cooling. Furthermore, small light caps (10mm) for assembly of the modules, i.e. behind a GFK wall and large light caps for assembly on the surface are enclosed. CASE-BEACON

A set of different light caps to build your own lights and cover simple light sources on your model. In contrast to deep-drawn products, the caps are made of high-quality polycarbonate, are impact-resistant, considerably more temperature-resistant and paintable. CAPS-PRO

A set of 5 small 10mm and 2 large 24mm, round light caps to build your own lights and cover simple light sources on your model. The caps are not deep-drawn but sprayed from high-quality Ploycarbobat, are impact/break-resistant and can be painted. CAPS-POINT

Makrolon for deep drawing with protective film on both sides for perfect surfaces. 0.75mm thick is very well suited to produce simple, low-depth glazing. All you need is a hot air dryer and the original model. Just heat it up properly until it is soft enough and then hold it at all four corners and pull it vigorously over the original object. 5 pieces with handy approx. 22x25cm. CAPS-MAKROLON-075

CAPS-MAKROLON-100

LIPO-2S-CHARGE

CAPS-BAR-L12

CASE-COOL-SLIM

CAPS-BAR-L15

CAPS-BAR12

FIBER-4

FIBER-3

CABLE-LIFEPO-4W

CABLE-LIFEPO-8W

CABLE-Y3-STROBE

CAPS-MICRO

CASE-MOUNT3040

CABLE-MICROSW

Unilight Connectors for DIY wiring (15) Standard connector enclosure for DIY crimping, 2 pole, 15 pieces with contacts CABLE-CONNECTOR