UNILIGHT NIGHTFLY BLADE DIY SET FOR LARGE MODELS 2,5M 4PCS.
Product number:
9744468
Manufacturer number:
NIGHT-L-DIYSET
GTIN/EAN:
912001868588
Description "UNILIGHT NIGHTFLY BLADE DIY SET FOR LARGE MODELS 2,5M 4PCS."
Perfect DIY kit for most large models up to 2.5m wingspan. The set consists of two wingblades for the wings and two tail-balds for the tail unit or rear fuselage.
No assembly slats are included. The safety connection set NIGHT-LXL-CONRG is available as an option.
uniLIGHT Night Blades
Compact dimensions with maximum performance
Minimal effect on flight behaviour
New type of cable and plug-free assembly
Optimized, adjustable cooling reflector
Reduced self-blinding
5 sizes for all scale rods
especially for wings and symmetrical for tailplane
Asymmetrical design for maximum robustness
Safety holder with position light available
large systems as cable and autonomous battery version
Assembly and operation
First, the enclosed small contact plate is glued firmly into the wing, side or elevator arch, preferably with good epoxy and pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In the plan view, right is always plus.
The connecting cable is routed centrally to the fuselage within the area. All Night-Blades can be used in parallel on a 2S LiPo battery, or on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off the unit during deep discharge could be fatal at night!
For commissioning, the Night-Blade is simply placed on the mounting plate with the two screws and tightened, the electrical contacting is done automatically. Make sure that the labels are always readable.
For the L and XL systems, the light panels must be aligned to the model once during initial installation and fixed with a little epoxy.
Then reflector surfaces are bent once so that the largest possible part of the light emission is directed to the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before aligning the surfaces with your hand or a small pair of pliers to prevent the joint from breaking open.
After the flight, the Night-Blades can be unscrewed and easily transported. No trace of the night flight system remains.
Technical specifications
Construction: 1.5mm GRP and GFRP/aluminium composite construction, 5mm CFRP tube, pre-assembled
Electrical: 8V, 2A/0.8A
Luminous intensity: ~1200 / 700 Lumen WHITE
Overall dimensions: 260x57mm / 210x57mm
Weight: 2x44g / 2x20g (without cable)
Delivery: 2x Wing-Blade, 2x Tail-Balde, ready for direct operation on 2S LiPo and on every uniLIGHT light control
No assembly slats are included. The safety connection set NIGHT-LXL-CONRG is available as an option.
uniLIGHT Night Blades
Compact dimensions with maximum performance
Minimal effect on flight behaviour
New type of cable and plug-free assembly
Optimized, adjustable cooling reflector
Reduced self-blinding
5 sizes for all scale rods
especially for wings and symmetrical for tailplane
Asymmetrical design for maximum robustness
Safety holder with position light available
large systems as cable and autonomous battery version
Assembly and operation
First, the enclosed small contact plate is glued firmly into the wing, side or elevator arch, preferably with good epoxy and pins. Make sure that the writing on the contact plates is legible so that the polarity is correct. In the plan view, right is always plus.
The connecting cable is routed centrally to the fuselage within the area. All Night-Blades can be used in parallel on a 2S LiPo battery, or on any uniLIGHT lighting control system. Pay attention to the excessive current load and sufficient battery capacity, switching off the unit during deep discharge could be fatal at night!
For commissioning, the Night-Blade is simply placed on the mounting plate with the two screws and tightened, the electrical contacting is done automatically. Make sure that the labels are always readable.
For the L and XL systems, the light panels must be aligned to the model once during initial installation and fixed with a little epoxy.
Then reflector surfaces are bent once so that the largest possible part of the light emission is directed to the model. ATTENTION: the reflector surfaces harden and can only be bent a few times. Fix the glued surface before aligning the surfaces with your hand or a small pair of pliers to prevent the joint from breaking open.
After the flight, the Night-Blades can be unscrewed and easily transported. No trace of the night flight system remains.
Technical specifications
Construction: 1.5mm GRP and GFRP/aluminium composite construction, 5mm CFRP tube, pre-assembled
Electrical: 8V, 2A/0.8A
Luminous intensity: ~1200 / 700 Lumen WHITE
Overall dimensions: 260x57mm / 210x57mm
Weight: 2x44g / 2x20g (without cable)
Delivery: 2x Wing-Blade, 2x Tail-Balde, ready for direct operation on 2S LiPo and on every uniLIGHT light control
Technical data
| Size (mm): | L |
|---|---|
| Sound oder Beleuchtung: | Beleuchtung |